Showing posts with label sound. Show all posts
Showing posts with label sound. Show all posts

Friday, September 12, 2014

Surround Sound Processor Circuit

Surround

This is the easy build surround sound processor schema using the digital delay process method. This audio processor isnt applying any unique function ICs that tough to obtain parsonaly, and designed in only common purpose ICs.

The kind of this Surround Processor is producing the surround impact with processing two channels of stereo supply. The majority of those are generates the surround impact with separates reverberations from supply signal and applies any processes, after which mix it to front channels or output as rear channel.

The schema works and contains three modules:

Separating the Reverberatins

The distinction in between each channels is separated with distinction amplifier from the op-amp. And greater frequencies inside the distinction signal are cut using the LPF.

A-D and D-A conversion

These are composed with common purpose ICs. The A-D converter is basically delta modurator that making use of a comparator plus a D type flip-flop. And it converts analog signal into digital data of one bit, 2 Msa/sec. Following passed digital delay, the bit stream is directly conversion into analog signal using the integrater.

It isnt beneficial that signal to noise ratio and distortion as this A-D, D-A converter.

Digital Delay

For the digital delay method, a DRAM chip is utilised as a FIFO memory. This schema design demands a 64K bit DRAM, but I utilized a 256K bit DRAM discovered within the junk box. Shift register generates Read-Modify-Write cycle, read out old data and save new data in a single cycle.

And lower byte in the address counter is assined as row address with the DRAM to increment row address every single cycle, to ensure that refresh cycle is often omitted. The FIFO length is 65536 bits and 2 Msa/sec makes 33 msec of delay time.

Surround sound processor schema source page: http://elm-chan.org/works/srp/report_e.html
Read More..

Tuesday, August 26, 2014

Simple Sound Operated Switch Wiring diagram Schematic

This is a Simple Sound Operated Switch Circuit Diagram. This sound-operated switch will sense the ring of the phone and translate this to a lamp that will go on and off. The amplified signal across R2 reaches D1 through capacitor C2. The rectified audio signals provide a negative bias for Q2, a pnp transistor. This causes Q2 to conduct so the current that triggers SCR1 is provided at the gate. Potentiometer R4 sets the sensitivity. R3 and C3 delay the operating voltage for Ql so that the schema will not be triggered on by the sound of the on/off switch, SI or by the current surge. Set the lamp atop a TV receiver, turn it on and set the potentiometer so that a finger snap at two feet will trigger the lamp on. Place the speaker close to the telephone and give it a try.

Simple Sound Operated Switch Circuit Diagram


Simple
Read More..

Monday, August 25, 2014

Build a Cuckoo Sound Generator Circuit Schematic

This schema generates a two-tone effect very much alike the cuckoo song. It can be used for door-bells or other purposes thanks to a built-in audio amplifier and loudspeaker. Used as a sound effect generator it can be connected to external amplifiers, tape recorders etc. In this case, the built-in audio amplifier and loudspeaker may be omitted and the output taken across C8 and ground. There are two options: free running, when SW1 is left open, and one-shot, when SW1 is closed. In this case a two-tone cuckoo song will be generated at each P1 pressing.

Cuckoo Sound Generator Circuit diagram:


Parts:

R1,R5___________1K 1/4W Resistors
R2_____________50K 1/2W Trimmer Cermet
R3______________8K2 1/4W Resistor
R4_____________82K 1/4W Resistor
R6______________1M 1/4W Resistor
R7,R17,R20,R21_22K 1/4W Resistors
R8,R10,R11,R19_10K 1/4W Resistors
R9____________150K 1/4W Resistor
R12_____________4K7 1/4W Resistor
R13___________100K 1/4W Resistor
R14___________220R 1/4W Resistor
R15,R22________20K 1/2W Trimmers Cermet
R16____________10R 1/4W Resistor
R18___________200K 1/2W Trimmer Cermet
C1,C11_________47nF 63V Polyester or Ceramic Capacitors
C2,C10,C12____220µF 25V Electrolytic Capacitors
C3____________220nF 63V Polyester or Ceramic Capacitor
C4_____________22nF 63V Polyester or Ceramic Capacitor
C5,C6,C8,C9___100nF 63V Polyester or Ceramic Capacitors
C7,C13,C14_____10µF 63V Electrolytic Capacitors
D1,D2,D3,D6__1N4148 75V 150mA Diodes
D4,D5_________BAT46 100V 150mA Schottky-barrier Diodes
Q1,Q2_________BC547 45V 100mA NPN Transistors
IC1____________7555 or TS555CN CMos Timer IC
IC2____________4093 Quad 2 input Schmitt NAND Gate IC
IC3____________4017 Decade counter with 10 decoded outputs IC
IC4___________LM386 Audio power amplifier IC
P1_____________SPST Pushbutton
SW1____________SPST Switch
SPKR___________8 Ohm Loudspeaker

Circuit Dis....
IC1 is wired as a square wave generator and produces both tones of the cuckoo song. The frequency of the higher one (667Hz) is set by means of Trimmer R2. When IC2D output goes low, a further Trimmer (R22) is added to IC1 timing components via D6, and the lower tone (545Hz) is generated. To imitate closely the cuckoo song, the square wave output of IC1 is converted to a quasi-sinusoidal wave form by R3, R4, C3 and C4, then mixed with the white noise generated by Q1, R6.

Q2 has two purposes: it mixes the two incoming signals and gates the resulting tone, shaping its attack and decay behavior by means of the parts wired around its Emitter. IC4 is the audio power amplifier driving the speaker and R15 is the volume control. The various sound and pause timings for the schema are provided by the clock generator IC2A driving the decade counter IC3. Some output pins of this IC are gated by IC2C, IC2D and related components to drive appropriately the sound generator and the sound gate.

When SW1 is left open the schema operates in the free-running mode and the cuckoo song is generated continuously. When SW1 is closed, the schema generates two tones then stops, because a high state appears at the last output pin (#11) of the decade counter IC: therefore the count is inhibited by means of D1 feeding pin #13. The schema is reset by a positive pulse at pin #15 of IC3 when P1 is pressed.

Setup:

Best results will be obtained if the two tones frequencies are set precisely, i.e. 667Hz for the first tone and 545Hz for the second: in musical terms this interval is called a Minor Third. Obviously a digital frequency counter, if available, would be the best tool to setup R2 and R22, but you can use a musical instrument, e.g. a piano or guitar, tuning-up the notes accurately by ear.
  • Disconnect temporarily R22 from D6 anode.
  • Connect the digital frequency counter to pin 3 of IC1.
  • Adjust R2 in order to read 667Hz on the display.
  • Connect R22 to negative ground and adjust it to read 545Hz on the display.
  • Restore R22 - D6 connection.
Tuning by ear:
  1. Disconnect temporarily R22 from D6 anode.
  2. Disconnect C8 from Q2 Collector and connect it to R4, C4 and C5 junction.
  3. Adjust R2 in order that the tone generated by the loudspeaker is at the same pitch of the reference note generated by your musical instrument. This reference note will be the E written on the stave in the fourth space when using the treble clef.
  4. Connect R22 to negative ground and adjust it in order that the tone generated by the loudspeaker is at the same pitch of the reference note generated by your musical instrument. This second reference note will be the C-sharp written on the stave in the third space when using the treble clef.
  5. Restore R22 - D6 and C8 to Q2 Collector connections.

Notes:
  • The master clock can be adjusted by means of R18.
  • The percentage of hiss and sound in the mixing schema, setting the tone character, can be varied changing R8 and R7 values respectively.
  • Any kind of dc voltage supply in the 12 - 15V range can be used, but please note that supply voltages below 12V will prevent operation of the white noise generator.
  • An amusing application of this schema is to use a photo-resistor in place of P1, then placing the unit near the flashing lamps of your Christmas tree. A sweet cuckoo song will be heard each time the lamp chosen will illuminate.
Source: Red Free Circuit Design

Read More..

Tuesday, August 12, 2014

Sight and Sound Metronome Wiring diagram Schematic

Sight and Sound Metronome Circuit Diagram. Precise, adjustable control of beats per minute from a largo of 18 to a frenzied, high presto of 500, These beats are produced acoustically through a speaker. A light flashes at the same rate. When SW1 is closed, CI begins to charge through Rl and R2. Cl will eventually reach a voltage at which the emitter of uni junction transistor is switched on, `dumping` the energy stored in Cl into an 8 ohm speaker. 

Sight and Sound Metronome Circuit Diagram

Sight and Sound Metronome Circuit Diagram

To produce a distinct `plop`, brief pulses across T2 secondary drive Q2 into conduction. The extra gain of Q3 and Q4 are sufficient to briefly switch LI on, then o£f; as the pulse wave pas-ses. Capacitor C2 `stretches` the puise slightly to overcome the thermal inertia of the lamp, so that a bright flash occurs,.
Read More..